2, brush the glue first glue on the wall, and then use a smooth spatula to spread the glue evenly, the general thickness of the glue is about 20mm. After brushing the glue, lay the Mosaic tiles in accordance with the drawing and align the gaps. Use a spatula knife to stick the Mosaic tiles tightly, or use a flat thick board to pad the horseOn the surface of the Seck tile, beat evenly with a rubber mallet to ensure that the paste is firm.
3, pre-glue: glue is to first apply a layer of glue on the wall. This is an important step in the paving of the Mosaic. Brush the walls with a mixture of tile glue or white cement. Apply evenly and evenly using special tools. The thickness of cement is preferably about 20mm. Paste Mosaic tiles: According to the design drawings, use good glue on the floor to spread the marcenaceous tiles on the wall. Every time the tile is laid, it must be firmly combined with the glue.
4, Mosaic tile paving method: basic treatment, leveling layer plastering, elastic line, divisionLay Mosaic, remove paper, adjust, wipe seam, clean. Base treatment: If it is a brick wall, wipe the bottom of the ash should first clean the wall, and finally water wet the wall. If it is a concrete wall, the loose concrete, mortar and other debris should be removed first, and the raised part should be chiselled flat.
5, step 1: glue in advance ▲ Glue is to brush a layer of glue on the wall first, which is an important step for Mosaic tile paving, brush the mixed tile glue or white cement on the wall, apply evenly and smoothly with special tools, and the thickness of the glue or white cement is preferably about 20mm.
Pre-gluing: Gluing is to apply a layer of glue to the wall first. This is an important step in the paving of the Mosaic. Brush the walls with a mixture of tile glue or white cement. Apply evenly and evenly using special tools. The thickness of cement is preferably about 20mm. Paste Mosaic tiles: According to the design drawings, use good glue on the floor to spread the marcenaceous tiles on the wall. Every time the tile is laid, it must be firmly combined with the glue.
Next, a brief introduction to the MosaicTile laying method. Brush glue Brush glue is the key to lay a good Mosaic, ready to mix the strong tile glue according to the proportion, use a spatula knife to smear the tile glue on the wall, pay attention to the amount of smear can not be too much. First of all, apply the glue on the wall, and then use a smooth spatula to apply the glue evenly, the general thickness of the glue is about 20mm.
Soak. First of all, before the tile is laid, it should be soaked in water, so that it can absorb enough moisture, so that the later laying can increase the viscosity of the cement and make the tile laying more firm. Cement. Second, when laying tiles, pay attention to the quality of cement, good cement,The viscosity and strength are very high, and it is not easy to paste the situation. Therefore, when people choose cement, they must choose the cement within the shelf life.
You can choose a special tile glue, neutral adhesive (use tile sealant two-in-one type. Also prepare gear scraper, caulking tool, basin, water, cleaning cloth. (Note that the Mosaic can not soak in water before). When laying, you should pay attention to the following points: When laying, if the Mosaic is pasted with mesh, it can be directly applied to the wall or the ground that has been coated with neutral paste, and the Mosaic is neatly laid.
MosaicTile laying method: base treatment, leveling layer plastering, elastic line, division, laying Mosaic, stripping paper, adjustment, wiping seam, cleaning. Base treatment: If it is a brick wall, wipe the bottom of the ash should first clean the wall, and finally water wet the wall. If it is a concrete wall, the loose concrete, mortar and other debris should be removed first, and the raised part should be chiselled flat.
Mosaic tile laying steps? E, the use of hard paste paving? The hard paste method is to sprinkle water on the screed layer that has been elastic, scrape a layer of plain cement slurry with a thickness of 1-2 mm, and then operate according to the soft paste method. Shortcomings of this approach