The first step: Before dismantling Huawei wireless adhesive , first long press the power button Huawei wireless adhesive , shut down the phone Huawei wireless adhesive , and then use the card pin to remove the SIM card tray Huawei wireless adhesive at the bottom of the fuselage. The following figure Huawei Wireless adhesive ; The SIM slot in the Mate20 Pro is also compatible with Huawei's pioneering Nano SD memory card, though you'll need a dedicated card reader.
The temperature is about 90 degrees. If the temperature set by the heating table is about 90 degrees, the heating time should be removed in about 4 minutes. Heat the phone and remove the screen, if the temperature is about 80 degrees. It'll be ready in a minute or two. When fully heated, use a blade to open a small opening. Since there is no line on the back cover of Huawei mate20pro, you can use a thin card to open it. After the back cover is opened, you can start to remove the parts.
Continue heating. mate20pro back cover blowing hot air for 5 minutes or not open because the heat is not enough, did not soften the adhesiveHow to remove adhesive
1. Apply face oil on the phone shell Huawei Wireless adhesive and evenly spread. Wait for a moment Huawei wireless adhesive , gently scrape off the softened adhesive Huawei Wireless adhesive with your fingernail, and then wipe with a damp cloth to remove. Use the hot air function of the hair dryer to heat the adhesive area. The glue will soften when heated, at this pointIt can be easily peeled off. Apply the cream to the adhesive and let it work for a few minutes. After that, the wind oil essence will dissolve the adhesive, which can be removed by gently wiping.
2. Try using an eraser. At the beginning, it may feel more and more dirty, but after a period of time, the adhesive will gradually loosen, and this method is more laborious and requires patience. Soaking the phone in water, adding a small amount of dish soap, and then scrubbing it with an old toothbrush can effectively remove the adhesive. With a cloth dipped in alcohol or erguotou, directly wipe the adhesive part, can also achieve the effect of removal.
3, with vinegar soaked cloth, cover the entire double-sided tape traceWait until the back glue is all soaked by the wet vinegar cloth, and gently remove the back glue with a ruler. You can use the usual nail polish to remove nail polish water, the nail water on the glue, wait a few minutes, the glue will fall off, you can now a small place to experiment.
4, how to remove the adhesive on the back of the phone? The following are several effective methods: wind oil essence method: The wind oil essence is applied to the area of adhesive residue, let it sit for a few minutes to take effect, and then gently wipe it clean with a damp cloth. Toothpaste method: Apply a small amount of toothpaste on the adhesive part, if the glue stain is dry, you can dilute it with water. Gently massage the stained area to make itSoften.
5, how to remove the glue on the phone case? Question 1: How to remove the adhesive on the mobile phone case? You can use an eraser. It's the fastest and most convenient. Question 2: The mobile phone case has been taped and left glue, what is the way to remove it? A mixture of soap and a little ammonia and turpentine can remove a lot of dirt and make the surface of the glass more shiny. With a good adhesive transparent adhesive repeatedly tear, you can remove some of the surface.
Will you before AnnThe process can be reversed and removed. Loosen the plastic nut, put the round head of the support rod into the nut, and press it tightly, and then tighten the plastic nut, and the assembly is complete. Uncover the two adhesive surface stickers on the support, choose to fix on the car surface, and press hard for a few minutes. The choice of car wireless charging bracket should not block the front car glass line of sight, and can not be too close to the outside, so as to avoid long-term sun exposure to affect its adhesion.
First of all, you need to prepare some tools to turn off the ignition switch of the car, so as not to short circuit or cause other safety problems. Second, you need to remove the shell of the Bex car charger, after removing the shell,You can access the internal structure of the car charger, according to the need, you can clean or replace the internal circuit board, capacitors, resistors and other parts, be careful when disassembling, do not damage any parts.
BSI has always been the leader of the car bracket industry, wireless charging of the car bracket is also the future trend, technology products or BSI do better, worthy of trust.
Required. Bsi ai car bracket has a built-in wireless charging function, which needs to be charged, and also supports wireless charging of up to 10W, and is compatible with all QI protocol wireless charging mobile phones on the market. Baseus (timesThink) is a new life digital brand of Shenzhen BSI Technology Co., LTD., which integrates research and development, design, production and sales. The brand takes meeting user needs as the core, creating practical and beautiful products, responsible for users, and adding a sense of gain for users.
Special adhesive for polytetrafluoroethylene. Polytetrafluoroethylene has excellent comprehensive properties, high temperature resistance, corrosion resistance, non-stick, self-lubrication, excellent dielectric properties, very low friction coefficient. Used as engineering plastics, can be made into polytetrafluoroethyleneOlefins, rods, belts, plates, films, etc., are generally used in corrosion-resistant pipes, containers, pumps, valves, and radar, high-frequency communication equipment, radio equipment, etc.
There are four production methods: ① emulsion spinning method (see chemical fiber spinning). Is the main method used in the industry, the average molecular weight of about 3 million, the particle size of 0.05 ~ 0.5m polytetrafluoroethylene emulsion (concentration 60%) and viscose silk or polyvinyl alcohol and other fiber carrier mixed, made of spinning liquid, spinning the carrier at high temperature carbonized away, the polymer is sintered and continuous fiber formation.
Plastic products can be broken with 502 glue to stick. 502 Glue is used for porous and absorbent materials, followed by steel, non-ferrous metals, rubber, leather, plastics, ceramics, wood, non-metallic ceramics, glass and flexible materials such as rubber products, shoes, soft, hard plastics and other adhesive or mutual. However, for polyethylene, polypropylene, polytetrafluoroethylene and other difficult materials, the surface needs to be special treatment, can be bonded.
Epoxy resin adhesive is widely used, can bond a variety of metals and alloys, ceramics, glass, wood, cardboard, plastic, concrete, stone, bamboo and other non-metalMaterials can also be bonded between metal and non-metal materials. There is no adhesion to untreated polyethylene, polypropylene, polytetrafluoroethylene, polystyrene, polyvinyl chloride and other plastics, and the bonding ability of soft materials such as rubber, leather and fabric is also poor.
M polytetrafluoroethylene tape bonding strength is very strong, for many surfaces can be quickly adhered to, showing excellent bonding strength. Use 3M Teflon tape black and yellow strip safety tape to mark and identify safe areas, this tape has unique tensile properties and has good adherence on irregular, curved and protruding surfaces after simultaneous useKeep it stretched and won't be lifted.
adhesive is based on α-cyanoacrylate, adding viscosifier, stabilizer, toughening agent, polymerization inhibitor, etc., through advanced production technology synthesis of a single component instant curing adhesive.