1, ① air conditioner Gree wireless charge wifi function is not opened: Press the wifi button on the remote control Gree wireless charging to open the wifi function Gree wireless charging , reconnect the ② wifi function of the air conditioner has been opened Gree wireless charging , but can not connect: press the remote controlThe "wifi" and "Mode" keys on the device are reset and reconnected. ③ The mobile APP connection operation is incorrect: please operate correctly according to the instructions. ④ Router compatibility problem: Please use the mobile phone hot spot connection test and reset the router.
2, first of all, the wireless network may not be turned on or the wireless network function of the air conditioner is turned off, you need to check the wireless network Settings of the router and the air conditioner. Second, the signal strength of the wireless network is not enough or is interfered with, you can try to adjust the location of the router, increase the number of antennas, or move the air conditioning to improve the signal reception. In addition, the distance between the air conditioner and the router is too far and the network is too wideWeak network signals or compatibility problems between the two may also cause connection failures.
3, check the Wi-Fi password: Please confirm that you entered the Wi-Fi password is correct, case sensitive, ensure that the password does not have its Gree wireless charge other characters and Spaces. Distance from the router: Make sure your air conditioner is no more than 10 meters away from the router and that there are no obstacles interfering. It is recommended to keep a sufficient distance between the air conditioner and the router. Check the network: Verify that the router is connected to the Internet.
The power supply voltage of the outdoor unit is insufficient. Gree Air conditioning e6 - Gree air conditioning e6 solution Gree wireless charging : (1) Replace the internal and external signal link line. (2) If the fault is still, please measure the power supply voltage of the signal port Gree wireless charge , if there is 0V-5V voltage, it indicates that the communication is no problem, and the fault should come from the frequency conversion motherboard or module.
Reset the air conditioner when the Gree air conditioner appearsE6 error code, first try to turn off the air conditioner power, wait a few minutes and then turn it on again, and observe whether the same error code occurs again. Sometimes, a simple reset operation can resolve a temporary communication failure. The E6 error may be related to the connection line between the indoor and outdoor units. Check whether the wiring is loose, damaged, or aged.
Communication failure, see if the black connection line with the outdoor unit is loose, if not, find after-sales maintenance. The display H6 indicates that the motor is blocked or the motor does not rotate. E6 means the inner machine is too dirty. Turn off the main power, open the lower cover, and remove the filterNet cleaning; Clean the electrostatic precipitator with a brush. Troubleshooting Methods and procedures for Gree Air conditioner E6 Replace the signal cables of the internal and external units.
The Gree air conditioner displays an E6 error due to the fault of the external engine board. The external engine board needs to be replaced. The detailed explanation is as follows: Gree Wireless charging : Identify the E6 error code Gree Wireless charging : When the Gree air conditioner displays the E6 error code, it usually means that the air conditioning system has encountered some kind of failure. This error code is usually associated with the circuit board of the air conditioner, especially on the external board. Outside of the machine plateFunction: The external engine board is an important part of the air conditioner and is responsible for controlling the operation of the external equipment of the air conditioner.
Gree air conditioning E6 is a communication failure, if the outer board failure caused, can only replace the outer board, it is not recommended that users replace themselves, it is best to contact the after-sales service or find professionals to replace the outer board, for this point still need to understand. Gree air conditioning use common problems: for the mobile phone that supports the infrared remote control function, if the air conditioner remote control can not be found, you can temporarily use the mobile phone to remote control the air conditioner, which is also more convenient.
Press firstKeep the "Set" key on Gree Wireless charging , and press the "Power" key at the same time, until the model code flashes in the window, release the two keys, press the "temperature plus" or "temperature minus" key, until the required code is displayed in the window and flashes. Press the "Set" key to exit and check whether the function of each key is correct. If it is correct, the setting is complete; If not, repeat steps 1-3 to set the next set of codes.
Air conditioning remote control to keep the air conditioning Gree wireless charging indoor unit. Select the mode and press "Mode" repeatedly"Button, will cycle" cooling, heating, dehumidification, air supply "four modes, according to Gree wireless charging you Gree wireless charging needs to choose, dehumidification is generally used back to the south, air supply is used when the fan. Press the switch button to turn the air conditioner on or off. Press the upper and lower keys of temperature adjustment to adjust the Gree wireless charge temperature you need.
Up-and-Down Wind button Press this key to swing the air deflector up and down to supply air. Press again to lock the current air supply Angle.Indoor Cleaning button When the following conditions are met, press this key to access the automatic indoor cleaning function. The air conditioner is turned off. The air conditioner is in cooling or dehumidifying mode before being turned off. Before pressing this key, the remote control setting temperature is less than the room temperature.
Manually open the air conditioner power supply, the remote control to the air conditioner acceptance window; Hold down the "Set" key (about 3 seconds), release when the model code flashes in the window, press the "temperature ▲" key, pay attention to the status of your air conditioner, until the air conditioner automatically starts, press the "Finish" key, the setting is complete.
Download and install "Gree Intelligent Air conditioner" APP; Open the wifi function of the air conditioner and enter the wifi setting mode; Connect the air conditioning wifi hotspot to secure the phoneAnd air conditioning in the same LAN; Open the APP, log in the account; Add air conditioning equipment to the APP and follow the prompts; Control the air conditioner in the APP, including switch, temperature adjustment, mode selection, timing switch and other functions.
The Gree air conditioner WiFi function can be used by following steps: First, make sure the air conditioner is running and find the WiFi icon on the air conditioner or remote control. After you press the WiFi icon, the air conditioner will start searching for nearby WiFi signals. In the list of searched WiFi, select the WiFi network you want to connect to, and enterCorrect WiFi name and password.
Check that the air conditioner supports WiFi connection. Not all Gree air conditioners can connect to WiFi, so you first need to check the owner's manual of the air conditioner or contact Gree customer service to confirm whether your air conditioner model supports this feature. Make sure the WiFi environment is good. Ensure that the home WiFi network is stable and has sufficient coverage so that the air conditioner can be connected smoothly. The air conditioner function Settings are displayed.
The cost of a simple air conditioning remote control signal receiver will not exceed 40 yuan, but to replace or buy a remote control signal receiver after the manufacturer, the manufacturer will charge at least 120 yuan, and some Japanese manufacturers may receive more than 200 yuan.
First determine that the remote control is good, and then measure whether there is 5V voltage in the positive 5V and ground in the receiver tripin, if there is, the remote control is also good, you can basically determine that the receiver is bad.
Depends on the specific type of air conditioning products. The remote control signal receiver above the household split wall-mounted air conditioning indoor unit is in the roomThe position of the display screen is in the middle of the return air panel. If it is a household split cabinet air conditioner, the remote control signal receiver is located in the middle of the operating panel of the indoor unit panel of the cabinet air conditioner.
That's a piece of protective plastic for the receiver. He's supposed to have buckles on the sides, just push them in. Be careful not to damage the glass when pressing.