1, oppo wireless headset is always on white light to enter the pairing mode, pairing OPPO Enco W31 support fast pairing function, just need to close to the phone when the Bluetooth is turned on, the phone will automatically pop up a quick pairing prompt, according to the screen prompt to complete the pairing. After the pairing is successful, the OPPO Enco W31 will pop up every time it connects to the OPPO phone, reminding the user of the remaining power of the left and right earphones and the charging bay, which can be said to be tenThat's very sweet.
2, hanging Bluetooth headset power display: Enco M3Enco M3Enco Q1 Wireless headset light red slow blinking indicates low power, red steady on indicates charging, green steady on indicates charging complete.
3, the Bluetooth headset has been flashing white light, this time the headset connection is faulty, it is recommended to use the following two methods to solve: the first method is to press the headset touch screen at the same time and wait for the headset to restart automatically after shutdown, so as to restore the factory Settings; The second scenario is to put two Bluetooth headphones into the headphone case, close the headphone case and restartYou can also reset and restore the headset to normal.
4, the white light of Oppo Enco Play usually indicates that it is in standby state or is being charged. When you place the Oppo Enco Play in the charging case and connect it to the power supply, it automatically starts charging and displays a white light. When the charging is complete, the bright white light will automatically turn off.
5. Check whether the headset has been paired with other mobile phones around. It is recommended that you put the headphones into the charging case, open the cover, and press and hold the function button to restore the factory Settings. Make sure the left and right ears are placed in the charging box and press and hold the charging boxThe lights will keep flashing. The user can disconnect the power adapter, then remove the battery of the headset, press the power button of the headset for 30 seconds to release static electricity, and then reinstall the battery to charge. If the white light is still blinking, there is a problem with the headset battery.
2, beatsx charging white light is always on Solution: Check your own charging cable is caused by poor contact, replace the original charging cable and try again. The charging mode is incorrect. Reinsert the charging cable and try again. Check whether the fault is caused by the battery. Check whether the battery is normal. Hardware problems caused, to the after-sales inspection and maintenance. beatsx can not turn on the machine charging always white light reasons: First, the power adapter can not recognize the headset battery.
3, press the power button no response, plug in the red and white light alternately three times after the white light is on - the head beam line problem. Unable to turn on, press the power button and flash the white light three times - head beam line problem. Can be charged normally, but can not be turned on - the head beam line problem.
4, the white light indicates that the battery is full. How BeatsX connects to an iphone: Turn on beatsx's Bluetooth, then open the iphone desktop and find the Settings options. After entering the main screen of Settings,We click the Bluetooth option to enter the Bluetooth interface and then in the Bluetooth interface, we can see the following figure, we can turn on Bluetooth here.
5. Take the beatsx white light blinking as an example. The causes and solutions are as follows: The charging cable is faulty. Check the charging cable or replace it. beatsx earphones can not be charged using mobile power supply, the volt of earphones is relatively small, can not be charged. After-sales maintenance. Carry warranty card, headphones, etc., to after-sales repair can be.
In fact, if the landlord's mobile phone is still the national bank system 2, don't tangle with the problem of lights. You learn to use Android first by setting up your phone's screen, connecting to your computer, and setting up wireless and WIFI connections. Finally, after learning to brush the machine yourself, the problem you said will be solved. Because you don't want to worry about it anymore. Unless your phone has a congenital defect, O (∩_∩) O ha ha ~ I came all the way, too.
My port water mb525 can be filled with line when I just bought it, and it took more than half a yearHowever, it can not be charged with the line, after plugging in the phone did not respond, change several chargers will not work, but can be flushed on the computer, I took the charger apart the usb socket in the middle of the idle two wires short connection can be charged, pay attention to can not be connected to other lines.
I used to have that problem. ! It turned out to be a plug problem. ! The one with the USB plug.
Unplug the battery and charge it, charge it more, and then go to the forum to find RSD and bottom package, drive.
May not rush in, ME525 try to use straight, with universal is easy to break the battery, my originalThe battery died after a few flushes.
I use my own original charger is fine, replaced by my dad's charger screen is dead ~ so I came to the conclusion that you change the original charger is good.