How to Connect a wire from each of the three contacts of the plug, open the patch board, leftThe hole on the left side of the plug is connected to one, the hole on the right side is connected to one on the right side, and the one in the middle is indirect. If there is a switch on the patch board, connect it in series on the firewire, measure with an electric pen on the patch board, and the bright side is the firewire.
First, you need to ensure that the voltage and current of the power cord meet the requirements of the charging board to avoid overload or damage to the device. Next, open the junction box of the charging board or the designated wiring area, and connect the live wire, neutral wire and ground wire of the power cord to the corresponding wiring terminals respectively according to the markings on the instruction manual or wiring diagram. In the wiring process, be sure to pay attention to the matching of the line color, and ensure that the connection is firmPrevent loose or poor contact.
Connect the solar power controller to the battery using the appropriate connection cable. Ensure that the positive electrode of the solar power controller is connected to the positive electrode of the battery, and the negative electrode is connected to the negative electrode of the battery. Next, connect the solar power controller to the solar panel with a cable. Likewise, the positive connects the positive and the negative connects the negative. After completing the above steps, the solar panel cable is successfully connected.
The wiring method of lithium battery charging is to connect the positive terminal of the charger to the positive terminal of the lithium battery pack, and the negative terminal of the charger to the negative charging terminal of the lithium battery pack. inWhen explaining this wiring process in detail, the first thing to note is that lithium battery packs typically contain multiple individual cells, which are combined in series or parallel to meet the voltage and capacity requirements of electric vehicles or other devices.
It is marked clearly on the figure: the top two corners receive the two poles of the rechargeable battery, and the left is positive and the right is negative; The following two corners are connected to the two poles of the approximately 5V DC input power supply, and the left is connected to the positive and the right is connected to the negative. However, your switchgear charging circuit has no perfect full detection and stop charging function, if not, then it is necessary to calculate accurately each time you charge, otherwise it may be bad battery and dangerousClose.
BAT and BAT- Connect the positive and negative terminals of the battery respectively.
Fixed wireless charger. Prepare a car wireless charger. Fix the 508l car with wireless charging in a suitable position in the cab. Connect one end of the USB data cable of the wireless charger to the car cigarette port and the other end to the wireless charger. After fixing the position of the wireless charger, ensure that it is stable and will not slide, the wiring is completed, and the phone can be charged.
Watts. According to the inquiry car home that 508l wireless charging is 10 watts. Place the charger and charging device in the appropriate position to ensure stable signal transmission and charging effect. At the same time, you should also follow the relevant guidelines and safety tips in the product manual to avoid battery damage or safety problems caused by improper operation.
No? The biggest upgrade of the 2022 Dongfeng Peugeot 508L is in terms of intelligent configuration, and the new car will be equipped with the mainstream ADAS intelligent driver assistance system, which can realize ACC adaptive cruise, AEBS high-speed emergency braking, and L, D-, D, G. Finally, the color of the Apple 5 data cable is red, black, green, white, V is connected to the positive electrode (red line), G is connected to the negative electrode (black line), D- is connected to the white line, D is connected to the green line, and you can stick it with tape.
For mobile phone chargers, when you need to connect five wires to two wires for charging, you should connect the red wire (VCC) and the black wire (GND) to the two wires according to the color corresponding. If you want to connect four wires for charging, you need to connect the red wire (VCC), black wire (GND), green wire (D), and white wire (D-) to each of the four wires according to the corresponding color.
Mobile phone charger 5 lines with 2 lines charging, only need to 5 lines in the red and black lines, according to the color of the two lines can be connected; To connect 4-wire charging, you need to connect the red, black, green and white lines in the 5 lines to the 4 lines respectively according to different colors. The two connections are shown below. 5-wire connection 2-wire charging connection. 5-wire connection 4-wire charging connection.
Use a lighter to charge the emergency wireless energy-saving lamp charging port line Wireless charging internal wiring Outer protective plastic sleeve burned wireless charging internal wiring , leaving enough long copper core wire. Wrap the two ends of the copper wire together. Wrap well with insulation tape.
① -- Connect the live line L ② -- connect the neutral line N ③④ -- connect the light source (suitable for the built-in drive LED light source) ③④ -- connect the drive power source, and then connect the light source (suitable for the external drive LED light source); ⑤ -- Connect the wall switch line, the other end of the switch line, the fire wire ① port, the wall switchOnly control the mains lighting, does not affect the emergency lighting; White socket - connects the battery pack.
Fire emergency sign light in the case of no power plug (three-wire wiring), generally red (dark red) power cord for the fire line; The blue power cable is the neutral cable Wireless charger internal cable : The yellow and green power cable is the ground cable. It can be used for reference when installing the wiring of fire emergency sign lamp.