1, the position of the milling cutter cover plate is not suitable, the opening is not parallel, the opening is insufficient or too large, the milling cutter cover plate should be re-installed, or the cover plate with serious wear should be replacedA castor. Milling cutter damaged or not sharp, should be replaced with a new milling cutter. Chute small sharp knife is too high or too low, the Angle is not correct, the small sharp knife is blunt, the Angle of the small sharp knife is correctly adjusted, and the small milling cutter is replaced.
2, may be the car motor is broken, may also be the sensor is broken, you can check to see. Of course, the least possible is that the switch is broken, and there are generally three cases. I hope this will help you. My side is Hangzhou Binder Technology Co., LTD., specializing in the production of adhesive machines, German technology, next time you can consider Ha.
3, the rubber machine suddenly appears before and after dislocation, indicating that the machine is in operationDuring the process, the unexpected situation caused by the incorrect use of techniques, so it must be repaired in time to achieve a safer use degree.
Wireless binding hot melt glue common Car wireless filling glue Quality problems mainly include page drop, uneven back, broken book core, foaming, book perforation at both ends.
Behind the bookblock milling bad bookblock is not neat or is not placed, should ensure that each paper in the end. Bookblock milling back when milling back amount is too little, shouldLower the book board so that the milling depth is 5-5mm (small milling cutter). The position of the milling cutter cover plate is not appropriate, the opening is not parallel, the opening is insufficient or too large, and the milling cutter cover plate should be re-installed, or the cover plate casters with serious wear car wireless filling glue should be replaced.
Different firmness of wireless adhesive only fixed with glue, no line, and the lock wire lock wire binding process is much stronger, such as adding car wireless filling glue two insurance Car wireless filling glue ; Different wireless adhesive installation In order to make the glue more firmly, before gluing, it is necessary to mill the back Car wireless filling glue ; The backrest of the book is fixed with stitches. In order to prevent the stitches from breaking, the back is not milling.
1, m glue is widely used in home, industry, construction and other fields. In the family, it can be used for home decoration, DIY handmade, etc. In industry, it is used in the manufacturing of automotive, electronics, aviation and other industriesAnd maintenance. In addition, this glue can also be used for bonding different materials, such as metal, plastic, glass, wood and so on.
2, different uses: ordinary glue is mostly used to fix some relatively simple things, such as the connection of paper. 3M glue is widely used in computers, mobile phones, communications, household appliances, audio-visual equipment, automobiles and other products.
3, the main components of M glue include polyurethane, epoxy resin, acrylate, cyanoacrylate resin, etc. These components make 3M glue has a strong adhesion, and can withstand high temperature, waterproof, anti-ultraviolet, anti-mold and so on. 3M glue also comes in a variety of forms,Such as liquid, tape, paste, film, solid, etc., each form has its own application range and characteristics.
4, M double-sided tape. 3M double-sided tape is widely used in computers, mobile phones, communications, household appliances, audio-visual equipment, automobiles and other products, should be selected according to the application of the product and environmental needs. When bonding 3M double-sided tape, perform the following operations to enhance the bonding effect: Clean and dry the adhesive surface first. It is generally recommended to wipe and clean the surface with a mixture of 1:1 IPA (isopropyl alcohol) and water soaked in cloth, and wait for the surface to dry completely.
5, M glue canIt is used to stick gold attribute items, and can be glued very firmly, and can also be used in some pasting of plastic, glass products, and plates, which can play a good pasting effect.
6, M glue has strong adhesive force, good fastness, waterproof and moisture-proof, high temperature resistance, strong load-bearing capacity and other properties, can be used for bonding, sealing and other applications.
The cover is sticky Car wireless filling glue : The upper sealing cylinder and the bottom plate of the forming mechanism are stickyGlue Car wireless filling glue , should be cleaned regularly and use methylsilicone oil prevention. If the gluing time of the back rubber wheel is too long, it is necessary to fine-tune the time and appropriately reduce the glue temperature to avoid wild glue. Cover folds or misalignment Car wireless filling glue : Adjust the position of the book clip, the height of the slotting knife and the glue temperature to ensure the correct clearance of the rubber scraper, as well as the cutting timing speed and drying time.
The book stitch, cut part is not rectangular should adjust the solid plate and book holder Car wireless filling glue Parallelism and verticality, so that the back stitching up and down.
Hinge is the problem that easily causes pages to drop and scattered pages in wireless binding. When folding by machine or hand, it is necessary to strictly control the size of the folding page out of the sleeve, and a folding page is glued to avoid missing pages. For books with thick book core or heavy paper quality, the depth of milling back is controlled within the appropriate range, and the thickness of the backing glue needs to be adjusted according to the actual situation to enhance the folding resistance of the back. Temperature control is crucial when using hot melt adhesives.
Milling back and waxing is the key step in wireless binding, milling back depth according to the thickness of the paper and the number of reduced layers to determine, the depth of waxing is also strictLattice requirements. If these steps are not handled properly, it will lead to insufficient glue penetration, resulting in page shedding and loose pages. Therefore, the quality inspection should not only check the precision of the milling back and wool, but also check the fine degree of the processing such as paging, bundling and compaction.
Hot melt adhesive damp, high water content, the most likely to produce bubbles, hot melt adhesive should be stored in a dry warehouse to avoid moisture. (2) The back of the milling back is uneven after grooving, and the gap is caused by the uneven glue on the back, check whether the milling cutter and the slotting knife are sharp, and on the contrary, timely replacement and grinding can be done to control the spread uniformity of the back glue. (3) The support plate is not parallel to the back of the bookWhere is the best place to install ETC? The ETC installation position of the car is generally in the middle and upper part of the front windshield, while large vehicles such as large trucks and buses are installed in the lower part of the middle. The height of the suitable installation position is not less than 2 meters, not higher than 5 meters, and the installation Angle should be between 30 and 90 degrees. If the vehicle itself has an explosion-proof film or is mounted with an explosion-proof film later, the signal transmission of the microwave communication link will be affected, and it should be installed in the microwave sunroof belt.
When installing automotive ETC equipment, it is strongly recommended to place it in the rearThe right side of the mirror to avoid interference with the driver's line of sight and ensure driving safety. Installation steps are as follows Car wireless filling glue : The first step is to prepare the ETC sensor device. Next, remove the tape from the back of the sensor and secure it to the right side of the front windshield rearview mirror. Finally, insert the ETC card.
For the installation location of ETC equipment for small vehicles, it is recommended to choose the middle and upper part of the front windshield, which does not affect the line of sight and is convenient for the use of the equipment. And large vehicles due to space limitations, ETC equipment should be installed in the lower part of the middle to ensureStable and does not interfere with driving. ETC electronic toll collection system is an intelligent toll collection method, its full name is road automatic toll collection system.
The ETC device is usually installed on the front windshield of the car, and is recommended to be installed in the upper left corner of the glass on the driver's side or behind the car endoscope. This will not affect the overall beauty of the car, but also ensure the efficient induction of the equipment. The installation steps are detailed as follows: Initial fixation: First, through a small round plastic suction cup, the base of the ETC sensor is firmly installed on the front windshield to ensure that the driver's line of sight is not blocked to ensure driving safety.
ETC installation location: There are usually two options for the installation location of the ETC, one is the upper left corner of the car, and the other is behind the endoscope. It is a non-parking electronic toll collection system, also known as road automatic toll collection system, mainly used in highways, Bridges, tunnels and some busy areas of the city, aiming to improve traffic efficiency and reduce urban traffic pressure. ETC untying process: For the untying of ETC card vehicles, certain procedures need to be followed.
ETC is generally placed on the front windshield of the car. However, depending on the vehicle type and height, the location of the installation will also vary. butThe installation height shall not be higher than 5 meters and shall not be lower than 2 meters. In addition, the installation Angle should be maintained between 30 degrees and 90 degrees. For large vehicles, it is generally installed in the lower middle, while common vans and cars are installed in the upper middle of the front windshield.
1, the choice of cost performance: Biaz car Bluetooth receiver, inexpensive, comparable to the sound quality of mobile phone headphones, even in the car sound effect is excellent, but also to create a theater like hearing enjoyment. Proprietary collateralQuality, reassuring.
2, as a high-tech enterprise born in China in 1996, Newman has three R & D and manufacturing centers in Hunan, Beijing and Shenzhen, focusing on the production and research and development of car Bluetooth receivers, its products enjoy a wide range of praise in the market. Senko is also favored for its superior sound quality and performance to meet your various needs. Please note that the brands mentioned above are not included in the comparison of competitive products.
3. In addition, the low power consumption and high sound quality of BASEUS BA01 USB Bluetooth adapter cable ensure that it can be saved during useSave power and provide better hearing enjoyment. Of course, there are other brands also worth paying attention to, such as China's high-tech enterprise Newman, its car Bluetooth receiver also enjoys a good reputation in the market. As a leader in multimedia audio, Rambler EDIFIER is also highly acclaimed for its Bluetooth audio brand.
4, in the brand choice of car Bluetooth receiver, recommend Philips, Newman and Iron Triangle. These brands excel in sound quality, providing a clear, realistic feel to the music. For example, Newman's in-car Bluetooth receiver uses advanced Bluetooth technology for stable transmission and excellent sound quality.Philips and Iron Triangle were also praised. When buying, choose the right brand and model based on your preferences and budget.
5, which brand of car Bluetooth receiver has good sound quality, Beisi car Bluetooth receiver, NetEase cloud music car Bluetooth receiver, King knob car Bluetooth receiver. Bsi car Bluetooth receiver BSI is a professional digital peripheral products, the quality is very good. The use of igniter connection, support charging function, can be double-mouth fast charging, you can play U disk. With intelligent digital display, it can automatically detect battery voltage and display playback channel.
6, for connected vehiclesBluetooth devices, there are a variety of brands on the market to choose from. Beisi car Bluetooth receiver is known for professional digital peripheral products, and its quality has been widely recognized. NetEase cloud music and King knob car Bluetooth receiver is also a good choice, NetEase cloud music especially pay attention to sound quality, and high charging efficiency, the volume is smaller than Himalaya, cost-effective.