If you use vivo mobile phone, wireless charging is also known as inductive charging or non-contact inductive charging, based on the principle of electromagnetic induction, it is not necessary to transfer electricity to the device like the traditional wired charger, but the device that needs to be charged can be charged by contacting the wireless charging base.
Hello, please charge the phone with the screen facing up in the center position of the charger or the position recommended by the charger manufacturer.
First, click on [Settings] on the desktop of your phone. Next, under the Settings menu, find and click on [Battery]. Finally, open the switch button on the right side of [wireless reverse charging]. The Huawei Mate30 Pro, a smartphone owned by Huawei, was unveiled in Munich, Germany, on September 19, 2019.
After turning on the phone, tap to enter the phone Settings. On your phone's Settings page, tap the Battery and Performance TAB. inGas, you can blow bubbles. The role of the hair dryer is to heat the bubbles when the nano glue blows, and the hair dryer can be not used if there are other heating methods.
- Pump production steps: cut a piece of nanotape. Rip off the tape. Fold the ends of the tape in half, making sure to pinch the middle tightly to seal the bottom. Use a hair dryer to heat the tape. Start pumping, pull out quickly and pinch tightly. Trim off any excess edges. Homemade pinch toys are done.
First cut a bar of the nanotape with scissors. With the glue side up, glue the straw tightly. And then glue on the bottom and the sides, be carefulStick it tight, and then don't glue the middle. After sticking, you can tear the film, and stick it tight again to avoid hollowing. Bake the nanoglue with a dryer and a lighter for a few minutes until the glue is soft.
Cut the nano glue into square sheets, fold in half and pinch tightly to form pockets. Use a straw to blow air into it and then heat it with a hair dryer for 30 seconds to create transparent bubbles. Adhesive painting: Nano-adhesive can be used as a binder to attach materials such as paper, yarn, and decorations to the tape, and then cut into the desired pattern to create patterns and artwork.
First of all wireless tape charging machine , gently open the cover of the charging bin wireless tape charging machine , and remove the headphones from the bin. Next, use a special pry bar or thin metal sheet to gently pry open along the seam of the charging compartment. There are usually hidden clasp, once found, press and hold the clasp to easily open the charging bay. After opening the charging compartment, the wireless glueTape machine You will see the detailed structure of the interior, as shown in the picture. Note that the battery is connected to the circuit board by a strip of wire.
Open the charging compartment and take out the headphones; Use a blade or scraper to pry open the gap, usually there will be a buckle, and then press the buckle to open; After opening, it is the full style of the interior, as shown below; The battery and the motherboard are connected by a row of cables; Glue between the battery and the circuit board, and use force to remove the battery.
Clear tools and preparations Before disassembling the charging bay, prepare proper tools, such as a screwdriver and a plastic opening tool. Make sure these tools don'tCan cause damage to surrounding materials. Most Bluetooth headphone charging bays are designed with removable parts, usually with openings at the interface or bottom. Look for these openings, which are usually open entrances.
Check the outside of the charging bay for screws or retaining clasp. Usually, these screws or clasp will be hidden under a sticker or rubber pad. Use a small screwdriver to remove the screws, or use a plastic pry bar to gently pry open the clasp. Note that some charging bins may not have screws or clasps, but are secured with adhesive. In this case, you need to be more careful to pry open the charging bay.
The method of removing the charging bin is as follows: Open the charging bin and take out the headset; Use a blade or scraper to pry open the gap, usually there will be a buckle, and then press the buckle to open; When it opens, it's all about the interior. The charging bay is for charging the Bluetooth headset. After using the Bluetooth headset, the user can directly connect the power supply to charge the headset. The charging compartment of the Bluetooth headset is broken, and you need to contact the official after-sales service of the brand manufacturer to ask whether it can be repaired after explaining the damage problem.
1, wireless glue machine common failure how to maintainRepair bookblock milling behind the bad bookblock is not neat or is not placed, should ensure that each paper to the end. When the back of the book is milling too little, the book board should be reduced, so that the milling depth is 5-5mm (small milling cutter). The position of the milling cutter cover plate is not appropriate, the opening is not parallel, the opening is insufficient or too large, and the milling cutter cover plate should be re-installed, or the cover casters of the wireless filling tape machine should be replaced.
2, the adhesive machine suddenly appeared before and after dislocation wireless filling tape machine , indicating that the machine in the process of operation, soThe unexpected situation caused by incorrect manipulation, so it must be repaired in time to achieve a safer use.
3, it may be that the car motor is broken, or the sensor is broken, you can check it. Of course, the least possible is that the switch is broken, and there are generally three cases. I hope this will help you. My side is Hangzhou Binder Technology Co., LTD., specializing in the production of adhesive machines, German technology, next time you can consider Ha.
4, maybe there are too many paper scraps inside the milling cutter, it is good to clear the paper scraps inside, I have repaired the machine is generally this problem.
5, you want to ask is the reason why the wireless rubber machine has been heating up? The reasons are as follows: Wireless tape charging machine : Long time use will cause the machine to heat up. The machine is used in high temperature environment. There is something wrong with the machine itself.
6, wireless gluing machine is the use of hot melt gluing, is to melt the glue at a certain temperature, after cooling solidified gluing, is automatically reset. Inside, the cover is glued on top, there is a common hot melt machine is very cheap, but need to use a special cover. There's glue on the cover. Different envelope thicknesses).