Pre-preparation: purchase of engines and equipment; Prepare the necessary tools (household tools); Understand the model structure similar to the real aircraft in advance; Remote control part, the ready-made remote control part can be installed.
divided into three partsSplit it up. Airframe, powertrain and remote control. Aircraft frame: Your preferred aircraft drawings, balsa wood or paulowne sheets, strips, heat shrink skins, glue, landing gear (buy ready-made), some control links, connectors, possibly carbon tubes (for the wings). This part is to do it yourself. In fact, they are all cad drawings now, directly cut out by laser, and then glue.
What needs to be prepared for the first homemade remote control aircraft is as follows: (personal experience, for reference only)? xml: namespace prefix= ns=urn:schemas-microsoft-com: office: office/? xml: namespace [Materials] Aircraft drawings, KT board, EPP or EPO foam board or foam block, 2cm wide double-sided tape, foam glue, 2cm wide transparent tape, 2 or 4cm wide fiber tape, 1mm steel wire 1 meter, 502 quick-drying glue.
Wing - is the device that generates lift during flight of the model aircraft and keeps the transverse side of the model aircraft stable during flight. Tail wing -- including horizontal tail wing and vertical tail wing two parts. The horizontal tail canMaintain the pitch stability of the model aircraft during flight, and the vertical tail maintains the direction stability of the model aircraft during flight. The elevator on the horizontal tail controls the lift of the model aircraft, and the rudder on the vertical tail controls the flight direction of the model aircraft.
Buy a foam fuselage remote control aircraft, about 150 up and down (and then spray J-10 and red star can be, pay attention to the point can look down) buy a J-10 aircraft model or download the picture, according to the model with blown cardboard to glue the remote control aircraft, so that the shape is like the J-10, mainly swept wings and tail nozzle, double vertical tail and other main signs. Adjust the center of gravity to the left, front and backSolid wing. This kind of wing is made of hard foam, according to the template, the hard foam is cut off, and the outside is covered with a layer of tissue paper. In order to ensure strength, trapezoids with relatively large thickness and small aspect ratio are often used. A wing. This structure is commonly used in small primary remote control model aircraft or electric model aircraft. Solid wing with spars and front and rear edges.
Divided into three parts, the aircraft body, the power system and the remote control system. Aircraft body: your preferred aircraft drawings, drawing requirements of balsa wood or paulownes sheet, strip, heat shrink skin, glue, landing gear (buy ready-made), some controlsConnecting rod, connecting piece, may use carbon tube (for insert wing). This part is to do it yourself. In fact, they are all cad drawings now, directly cut out by laser, and then glue.
Preparation: purchase of engines and equipment; Prepare the necessary tools (household tools); Understand the model structure similar to the real aircraft in advance; Remote control part, the ready-made remote control part can be installed.
Remote control aircraft model production method diagram as follows to determine the aircraft model type: according to personal preferences and needs, choose the appropriate aircraft model type, the common solid/p>
Production steps: Take the ballpoint pen cap, make vertical and horizontal cuts at the bottom of the cap, bend the cut part to make two small wings, bend the tail, as the fuselage of the helicopter model. Take a piece of blue cardboard, cut it into two long strips of 5cm with scissors, make a cross, and paste it together with tape or glue as the propeller of the airplane model.
The method of making a model airplane is as follows: Use a ballpoint pen to draw each part of the airplane on a foam board. Cut it out with scissors. Attach the parts of the aircraft to the fuselage of the aircraft. aeroplaneA small hole is cut into the fuselage, and the wings are installed in the middle of the fuselage. Adjust the balance of the wings of the aircraft and tape each part in place.
How to make a model plane? Materials and tools: Wings and fuselage Materials: Foam sheets, bamboo, wood, and plastic are commonly used to make the wings and fuselage of an aircraft. Drive system: includes motor, propeller, electronic speed controller (ESC) and battery. Remote control system: remote control, receiver, steering gear, etc., used to control the aircraft. Glue, tape and scissors: Used to assemble and secure aircraft parts.
Aircraft model production methods such asNext: Make the fuselage, the fuselage is the main part of the connection to other parts, first find a 3mm thick tung board, and then use a pencil to outline the rough outline on it, and then you can cut the knife. When cutting must pay attention to the technique, do not be careless. After the shape is determined, the surface is polished with a wood file and sandpaper, which is strictly said to be streamlined.
Certainly. There are professional modifications abroad, theCar engines can be adapted for use in aircraft. There are also people in the country, but mainly motorcycle engines and motor boat engines.
In fact, now are cad drawings, directly laser cut out, and then glue. Power system: methanol engine (or gasoline engine), fuel tank, oil pipe. If you do electric, you need a brushless motor, electronic governor, battery. And the propeller. This part must be purchased ready-made. Remote control system: transmitter, receiver, steering gear (4-6), cable, receiver battery. This part is definitely to be purchased ready-made.
Yes, we canThere used to be a paraglider to be converted into a powered paraglider need to install a power unit, usually using gasoline or diesel engine!! The specific price depends on the materials you use. Generally, it takes several thousand to ten thousand to refit well.
No power: generally used in gliders, although no power is actually the use of the earth's gravity to generate speed and speed naturally has lift to soar to the sky. Electric: The use of batteries or other means such as solar panels to generate electricity to drive electric motors to generate thrust. Wood engine: Most of the remote control aircraft use this power mode, it usesThe fuel is lignin (methanol).
"We'll have to make the engine ourselves." With the help of a mechanic named Dila, after a long time and a lot of effort, they built a gasoline engine with four cylinders and 12 horsepower, weighing only 70 kilograms. With the engine, the next step must be to solve the problem of the propeller.