1, the vehicle flow card replacement steps are as follows: prepare a new mobile flow card and a tool to open the card slot. Usually, there are instructions on the location and opening of the mobile data card in the Settings of the center control screen in the car, and you can follow the instructions to find the card slot and open it.Take out the old mobile data card, be careful not to exert too much force to avoid damaging the card slot or card.
2. There are two ways to recharge the traffic for the vehicle: operate on the center control screen or insert the traffic card on the recorder. 1 If the recorder supports WiFi, the phone hotspot can be opened and shared with the recorder, provided that the phone has traffic. 1 Consult the navigation manufacturer whether the traffic card can be replaced, if the traffic card is external, you can replace it by yourself; If it is built-in, manufacturer assistance is required.
3, first, find BYD e2 vehicle system. Then, locate the flow card card slot andPull out the original old data card. Finally, insert the new flow card into the card slot.
Need to check whether it is a problem of poor contact. It is best to use the original charger and data cable to check whether it is the problem of the phone itself. Then check whether there is poor contact inside the charging data cable. Then check the charging data cable plug and the mobile phone charging tail plug, whether there is poor contact between the two.
So the knotWiring , cut into pieces and put together. Place the cut ingredients in a juicing glass. You can appropriately add water radish wireless charging cable , you can also not put radish wireless charging cable , the water will dilute the juice radish wireless charging cable , cover the lid of the cup and wait for 40 seconds. Clean up the juice cup after drinking, the juice cup is more convenient to clean, and the water can be flushed.
Blade is only used for playing fruits and vegetables, do not play grains and other hard things, cooked or soakedSoft can be added to the liquid juice, a single run is not more than a minute, it is best within 15 seconds, playing stop and stop is more conducive to motor maintenance, general fruits and vegetables a few seconds to get radish wireless charging wire ; After the juice is finished, turn counterclockwise to loosen the card slot. After the motor is stopped, pull the portable cup out of the host valley.
First wash and peel the cucumber. Cut the cucumber into small pieces with a knife. Clean the juice glass and put the cucumber in it. With or without water, open the juicer glass. If you drain the water, the juice will be diluted. Once the cup is covered, pressOne click start, wait 40 seconds. Remove the lid and pour out the juice. Wash the juice glass and put it back where it belongs. Wash and peel the fruit.
1, through cable connection This connection requires the use of cable, the current more common is HDMI, USB, Type-C and other cable. The steps are as follows: Prepare the cable. Select the appropriate connection cable according to the interface type of the phone and the projector. Plug one end of the cable into the appropriate port on the projector and the other end into the phoneCorresponding interface. Turn on the projector and select the appropriate input signal source.
2, how to use the screen instrument 1 Wireless connection in the case of WiFi. In the case that the projector can use WiFi, and the phone and the projector are in the same network environment, open the screen projection software of the phone and the projector respectively, find the corresponding projector model in the phone, and click to connect. If the phone comes with a wireless projection screen, find the corresponding projector model in the phone. Wireless connection without WiFi.
3, how to connect the screen projection instrument to the mobile phone screen projection 1 when there is WiFiThe wireless connection. In the case that the projector can use WiFi, and the phone and the projector are in the same network environment, open the screen projection software of the phone and the projector respectively, find the corresponding projector model in the phone, and click to connect. If the phone comes with a wireless projection screen, find the corresponding projector model in the phone. Wireless connection without WiFi.
4, Step 1: First plug in the power cord of the projector and notebook. Step 2: Then connect the video cable to the computer and the projector respectively, of course, plug in the audio cable of the power amplifier. Step 3: Turn on the power switch of the projectorThere will be a power light on the right. Of course, the computer should be turned on.
5, win10 screen projection function Use method wireless screen projection function. We open the feature list and select Connect. After clicking the connection, win10 can start the search function to search for wireless projection support devices in the environment. In addition, we can also click on the projection. It can be found that in addition to the four forms of projection, there is also a button to search for wireless projection devices.
6, plug the same screen device into the display device (such as TV), select the signal source with the remote control to the same screen device, press the adjustment button to mirrorcast interface, open the phone Settings - display - wireless display, search for the device, the connection can be the same screen. Mobile phone connection projection method: Method 1: DLNA/Miracast/Airplay wireless protocol connection This method is mainly used for intelligent projection equipment.