1, the installation steps of your previous wireless charge how to disassemble can be removed in turn. Loosen the plastic nut How to remove the , the support rod round head into the nut, and press tight, and then tighten the plastic nut, the assembly is complete. Uncover the wireless charge on the bracketHow to remove the two adhesive surface stickers of , choose to fix on the car surface, and press hard for a few minutes. The choice of car wireless charging bracket should not block the front car glass line of sight, and can not be too close to the outside, so as to avoid long-term sun exposure to affect its adhesion.
2, first of all, you need to prepare some tools to turn off the ignition switch of the car, so as not to short circuit or cause other safety problems. Second, you need to remove the shell of the car charger, remove the shell, you can access the internal structure of the car charger, according to the need, you can clean or replace the internal circuit board, capacitors, electricityResistors and other parts, be careful when disassembling, do not damage any parts.
3. Bsi ai car bracket has a built-in wireless charging function, which needs to be charged, and also supports wireless charging of up to 10W, and is compatible with all QI protocol wireless charging mobile phones on the market. Baseus (BaseUS) is a new life digital brand of Shenzhen BaseUS Technology Co., LTD., which integrates research and development, design, production and sales. The brand takes meeting user needs as the core, creating practical and beautiful products, doing its duty for users, and adding a sense of gain for users.
4, charging speed is very satisfactory, need to improve the solutionThe touch key of the lock should be placed on the left side, because the mobile phone is basically placed on the right side of the main driver, and it is easy to mistakenly touch the mobile phone with the right hand, and the left side can be perfectly solved. PHILIPS car off the key can also induction open, this function is practical, parking and pulling the key can also be electric opening and closing, it is estimated that there is a built-in battery, charging speed may be the reason for the charging head is not fast charging.
5, through the best Tmall Genie AI intelligent voice car wireless charging stand voice control to make a call.
6, there is no need to manually change the song when the vehicle is driving, just say what you wantListen to the tracks, BSI AI Tmall genie car wireless charging bracket will immediately play the tracks you say.
Observe the mobile phone stand wireless charge how to disassemble fixing method Wireless charge how to disassemble , there are screws, clasps or other fixed devices Wireless charge how to disassemble , use the corresponding screwdriver or wrench, turn the screw counterclockwiseSilk, remove them one by one. Once the fixture is removed, the parts of the bracket can be gently separated.
2. The steps for disassembling the MG 6 wireless charging board are as follows: First twistRemove the fixing screws at the four corners of the panel and remove the shielding cover plate on the front of the wireless charger. Shield cover plate back edge exposed copper, black oil insulation in the middle, screen printing PCB-01. The shielding cover plate is made of PCB and has shielding copper foil on it to reduce electromagnetic radiation interference. Inside the aluminum shield case are three wireless charging coils, which are fixed to the shield of the PCBA.
3, put the mobile phone with wireless charging function on the wireless charging board. The position should be placed, you can charge, note that some wireless charging panels support different mobile phone models, to choose wireless charging panels according to their mobile phone models, currently does not support long-distanceCharging, may later reach this technology, what is wireless charging technology can be remote wireless charger, this charger contains a transmitter with a plug.
The method is as follows: unscrew, remove the whole shift frame, from the bottom line. After fixing the charger, insert the line along the lower gear shift to the interior panel in the position of the main driver seat, remove the lower line to extend to the fuse box. Connect the power supply to the safety box, connect the negative electrode, and restore. Byd Co., LTD (JanByd was founded in February 1995 and is headquartered in Shenzhen, Guangdong Province.
BYD Han's wireless charging switch is located in front of the central armrest. Byd Han's length, width and height are 4950*1890*1490mm, and the wheelbase of the body reaches 2940mm, which is expected to be a medium and large car. In terms of configuration, BYD Han is equipped with a wealth of configurations, such as ACC adaptive cruise, electric suction door, head-up display, parallel assistance, lane keeping assistance, and induction open luggage.
Yes. Byd Han wireless charging function, on the helpHand box in front of the space, as long as the phone supports wireless charging, put on it.
The mobile phone wireless charging area of BYD Han EV model is located in the front of the central armrest storage box of the center console. When the vehicle power gear is in the "OK" gear, the phone can be placed on the non-slip rubber mat in the wireless charging area, with the phone screen facing up. In this position, the phone will automatically start wireless charging, and the charging icon will be displayed on the multimedia UI interface.
Yes. Byd Han dm wireless charging Settings are as follows: BYD Han EV mobile phone wireless charging area is located in the center console central armrestMake sure the battery is removed. Find the fixing method: Observe the wireless charger on the nightstand to see how it is fixed on the nightstand. Usually, the wireless charger is fixed to the nightstand by screws, or by using glue or other adhesives.
This panel is a coil combination, so that the phone can be conveniently placed anywhere on the panel can be charged, without alignment. Its internal structure is roughly as follows: the shortcomings are not without, because the multi-coil wireless charging board product has as many as a dozen or even several wireless charging coils built in, and the problem in heating cannot be underestimated.
Yes. In addition toDo not take off the battery of the mobile phone, otherwise there is radiation, so the wireless charging of the bedside table has an impact on the mobile phone, wireless charging is not through the connector or metal contact as a medium, to carry out power transmission technology. Also known as inductive charging, non-contact charging, etc.