Connect the plug first. Peel off one end of the wire to reveal two metal wires. Use a screwdriver to remove the protective cover of the plug and loosen the wiring screws on the metal plate of the plug. Wrap the two peeled metal wires around each of the two metal pieces of the plug, and then tighten the connecting screws. Then put the plug protection case in place, screw on the screw, and the plug is installed. Connect the board.
Know where the main brake is, if it is an air switch, turn it to the off. Test it with a test pen, and if it runs out of power, you can start preparing for operation. If you don't have a pencil, take a good lamp and plug it into a wall outlet. Turn on the switch and the light won't turn on.
wireless socket how to wire First good screwdriver, three-hole wireless converter socket, plug, wire, and then the power cord coat off, exposing the copper wire inside, and then the wireless socket and plug withOpen the screwdriver, loosen the buckle and the orange wiring terminal, and prepare to connect cables. First screw on the power cord, the red is connected to the L pole, the blue is connected to the N pole, and the yellow and green are connected to the E pole.
1. Fix the power cord with screws. Secure the power cable with a crimping bar. Close the back cover Deli wireless charging disassembly , tighten the screws Deli wireless charging disassembly , you can plug in the power socket to use Wireless charger disassembled .
2, the use of wireless charging is very simple, just follow the following steps wireless charging disassembly : Plug the charger into the power outlet, and place it on the desktop or other smooth surface. Plug the wireless charging receiver into the charging port of your device. Place the device in the charging area of the charger. Wait for the device to be fully charged. What are the advantages and disadvantages of wireless charging? Advantages of wireless charging: Convenience: no need to use a wire connection, you can charge anytime, anywhere.
4, when using the wireless charger, just connect the USB cable and plug it into the socket. When the battery is out of power or about to be out of power, put the phone on the charger board. The charger and the phone will be connected and charged in an instant, and the battery icon at the top of the phone screen will be displayed when chargingCharging state.
Wireless socket does not need point-to-point transmission wireless charging and disassembly , and can be used through the wall, remote control distance up to 100M or so, the load can reach 500W, widely used. Wireless smart socket Wireless smart socket using Deli wireless charging and disassembly is infrared receiving technology and sensor technology, can intelligently identify current changes and external receiving voltage changes, to achieve intelligent controlThe switch and standby function of the electric appliance achieve the purpose of intelligent power saving and safety.
First, install the power cord: Remove the jacket of the power cord to expose the copper wire inside. Second, open the socket: Use a screwdriver to open the wireless socket and plug. Then, remove the buckle and wiring terminals. Remove the buckle and orange wiring terminals and prepare to connect cables. Next, connect the wires: connect the red wire to the L pole, the blue wire to the N pole, and connect the yellow and green wire to the E pole.
Fasten the power cord with screws. Secure the power cable with a crimping bar. Close the back cover, tighten the screws, you can plug in the powerThe seat is in use.
First of all, you need to click the power button on the wireless intelligent operation to restore the wireless socket to the factory Settings; Then open the APP of the wireless smart socket on the phone, enter the wireless password to set it; After the successful setting, you can return to the control interface, and finally you can operate the wireless smart socket through the remote control or the mobile phone.
Take a brand of smart socket as an example: Install the WiFi version of the smart socket on the AC power strip board, and the socket shows a yellow light indicating that it is in pairing mode. Open the brand APP corresponding to the smart socket on the mobile phone and click "" in the upper right corner of the home page.>
Millet 55W vertical air-cooled wireless charging using PC flame retardant material plastic shell, fuselage edge clear end Angle arc transition, support board is black, base sandblasting treatment is gold. From the front, the front end of the base is equipped with LED indicators, and the support board is layered above and below, using different designs. Indicator light is green when working.
Mi 55W vertical air-cooled wireless chargingThere is a special bracket, can be installed directly on the base, and is embedded, especially stable! It can be removed at any time when not in use, because it is specially configured for the Mi 10 Ultra, and it is generally not used.
Mi 9 Pro supports 55W vertical air-cooled wireless fast charging, but there will be no fan rotation during the charging process. This is normal, because during fast charging, the phone will emit some heat, but it is not too high, so it does not need a fan to turn to dissipate heat.
Compared with the common 10W wireless charging technology on the market, Xiaomi's 30W wireless flash charge can charge half of the 4000mAh battery in 25 minutes, achieving "wireless beyond wired" efficiency. Xiaomi's vertical air-cooled wireless charge 30W is cleverly designed with an ergonomic tilt, which is convenient for users to operate while charging, and the built-in ultra-quiet fan can effectively actively dissipate heat, improving the comfort of the charging process.
Millet vertical air-cooled wireless charger (55W black) 199 yuan at present millet maximum power (charging speed) wireless charger, if the phone is 30W or 33W wireless charging power, then it is recommended to largeHome "redundancy" to buy this high-power wireless charger, because the mobile phone upgrade faster, and wireless charger this product can be used for several years, in the future for a new mobile phone can also do power coverage.