1, the mouth of the air pump is aimed at the palm to pump, see if there is suction, if there is suction, it means that the pump is good, if there is suction, it means that the pump is good, because it is a manual air pump, pumping a little laborious, it is recommended to use the hand before pumping part of the air in the bag, so as to save effort, It takes about one to three minutes to smoke a big bag.
2, it is recommended to put some butter back, or replace one. It's from the seal. fromThe sand and stone of the gray sky land was replaced by a tall and valuable item transportation, and it was found that it was really comfortable, when the cargo was not pulled, the balloon was put into some air, and it was comfortable to open home, pull the goods, and it was full of gas, and it still could not affect the cargo. To the unloading site, found that their car and the unloading platform almost distance. As soon as the air pump starts, the car is level with the unloading platform.
3, check the sealing: if it is difficult to pump air or can not pump air at all, first check whether the sealing of the bag is good. If the seal is not good, it may cause the gas to not be fully extracted, which affects the effect of the storage bag. Replace the gasket: The seal of the pumpThe pad is a key component to ensure that it fits into the mouth of the bag, thus achieving a gas mass seal. When the gasket is aged or damaged, replace it with a new one.
4, under normal circumstances, the car squatted, the tire is out of air, and the air pump can not be hit, most likely because the tire has a leak gap, rather than completely scrapped. First, you can check the tire for external breakage, cracks, or other visual defects, and if so, it indicates that the tire is scrapped.
5, use the slide to zip up the compression bag, stop when it is pulled to one-third of the part, squeeze the bag with your hand, and give most of the air insidePress it out and then pull the rest of it up. Then open the air nozzle cover on the compression bag and connect the interface of the manual air pump. Then start pulling the piston back and forth, wait until the compression bag is flat and the air inside is pumped out, and then cover the air nozzle cover.
6, the dowel inserted under the hose to the oxygen injection port there is directional, inserted backwards, there is no air out. Lift the pump up a little, let the air out of the oxygen nozzle, and then slowly lower it.
1, first do the sealing of the compression bagCheck to make sure there are no air leaks. Use the slide to zip up the zipper of the compression bag, stop when it is pulled to one-third of the part, squeeze the bag with your hand to press out most of the air inside, and then pull up the remaining part. Then open the air nozzle cover of the wireless air pump on the compression bag, and connect the interface of the manual air pump to it.
2, Problem 1: How to use the bag manual air pump after the bag is confirmed to be sealed, the hole of the pump is aligned with the air hole on the bag, and it can be used after being fastened, which is like pumping a bicycle tire. qQuestion 2: How to seal a manual air pump with a confirmed compression bag. Open the small round cover on the back of the bag and connect the air pump interface successfully. Start pumping air, kind of like pumping up a bike.
3, the method of use: the vacuum pump of the air conditioner has a joint, respectively connected to the pressure gauge and the joint in the opposite direction of the meter head wireless charging and pumping pump ; Connect the joint of the pressure gauge stem in the opposite direction to the machine joint that needs to be evacuated; Run the air conditioner vacuum pump until the pressure gauge pointer is close to negative one indefinitely; Tighten the pressure gauge stem, turn off the vacuum pump, and evacuate the end.
4, the use of manual air pump: before putting the clothing quilt into the compression bag, dry the clothing quilt first, and then fold it into a shape that is convenient for storage, and put it into the bag as far as possible, at least a few centimeters away from the sealing zipper. Before closing the zipper, check whether the sealing part of the zipper is clean and whether there are fine fibers or dust. Fine fibers or dust may reduce the tightness of the compression bag and cause air leakage in the compression bag. If yes, please wipe it with a wet rag.
5, you can use a vacuum cleaner or pump to pump air, before pumping to loosen the valve 5 rings, the vacuum cleaner or pump mouth to the door began to pump air, the bag airAfter suction, quickly pull out the suction nozzle and tighten the air valve, and press the dust cover firmly. (Pay attention to those who use the pump, because the big bag is long when it is pumped, this time it is not necessary to pump it all at once, and you can stop in the middle and tighten the pumping valve, so that the air will not go in.
The compressor has three copper pipe joints, we only need to keep one out, one air intake can be, the third maintenance use of the filling port, sealed with a welding gun. It is recommended to buy an old compressor at the maintenance center, please help the maintenance centerBusy transformation, welding a copper joint in the compressor air inlet and air outlet, so that we can use the gas pipe connection in the future.
Can also, it is best to buy 8 wire, PA PE material, buy more to see, a lot of specifications. Byett uses video v/show/wmsydFYNkAC_6cV0.html compression bag types Vacuum compression bags can be divided into three categories according to the exhaust method: the first type: exhaust type, through the external exhaust equipment such as an air pump or vacuum cleaner, to exhaust.
Yes. Centrifugal pump and centrifugal windBag pump can send express, air pump, refers to a suction nozzle, exhaust nozzle each, and can continue to form a vacuum or negative pressure at the inlet, compression bag pump without the interface, electric strong compression, can send express, overheating protection, safety and rest assured.
3, of course, the electric pump is good, because the electric pump has the role of continuous pumping, its efficiency is high, and the manual pump is laborious and time-consuming, so the electric pump is easy to use.
4, the electric pump of the vacuum storage bag can not pump ordinary plastic bags. The vacuum storage bag is smooth, the electric air pump power is large, andAnd there are special Settings, you can suck out the air inside, ordinary plastic bags are too thin, the bag will be damaged when pumped.
Manual air pump inflation air mattress inflation If there is no electric air pump at home wireless air pump , then you can buy a hand play wireless air pump Wireless air pump , chargeThe gas method is the same as the electric air pump, first find the inflation port. Then, the air pump nozzle is aligned with the inflating port, and the inflating mattress is manually inflated. (3) The use of air duct If there is a air duct, you can use the air duct to inflate the air mattress, make a funnel, wrap the large air cylinder mouth, and reach into the small air outlet to inflate.
After the mattress is unfurled, the wireless air pump We need to inflate it. Inflation can be used in three ways: air pump, electric pump or artificial air blowing. If you are using an air pump or electric pump, connect the inflation tube to the inflation port of the mattress, turn on the power, you can startDynamic inflation. If it is manually inflated, the simple way is to gently inhale with your lips against the inflator, and then keep blowing through your mouth until the mattress is full of air.
Air mattress Place the self-inflating mattress on the ground and plug the power plug into the outlet. Turn on the air pump power switch and wait for the mattress to automatically inflate to full state. This process takes about 3-5 minutes, depending on the size of the mattress and how fast it is inflated. Adjusting the hardness After the self-inflating mattress is inflated, you can adjust the hardness according to your needs. If you feel that the mattress is too hard, you can let some air out, and otherwise you can add air.
The interior of the self-inflating cushion is generally built with a high rebound full fat sponge. The inflatable cushion usually has an air nozzle on the side,When we open the inflatable nozzle, the high rebound full fat sponge inside will automatically expand and automatically enter the air. When the inflatable cushion is inflated and reaches the normal state, then the lid of the inflatable mouth will be covered and tightened, and then it can be used.